Dewin Technology Company Limited · Factory in Vietnam
Rectangular Webbing Rings
We check ring dimensions against your folded, sewn webbing before we quote. U.S. distributors, private-label and wholesale buyers can send a drawing, photo or sample details for rectangular rings that join webbing loops, and our factory team will review the fit with you.
Start With the Webbing, Then Size the Ring
A rectangular ring is a metal component for webbing, not a buckle or a hook, so the sourcing decision is whether its slot and corners suit the folded, sewn webbing you plan to run through it. We start from your strap drawing, then confirm the ring dimensions, closure and finish that belong with it.
Select a Rectangular Ring Configuration
Before choosing a rectangular webbing ring, confirm how the webbing wraps it: the internal width and height must clear the folded, sewn strap with room for the seam, while the wire diameter or plate thickness, corner radius, seam or weld type, and finish decide fit and handling. Send these details with a drawing or photo, and we will match them to a configuration.

Metal rectangular webbing ring
Catalog p. 17 family reference
The photograph shows the ring family. Internal width and height, section, corners, seam or weld, material grade and finish are specified with your quotation.
Ring built to your drawing or sample
Specified with your quotation
Send your webbing width in in, how the loop is folded and sewn, and a drawing, photo or sample ring. We match the opening, ring body, closure and finish to your brief before we quote.
Fit the Slot to Folded Webbing
The first decision is the opening. Webbing that is folded back and sewn is thicker than a single layer, so the ring's internal width and height must allow the sewn loop to pass and sit flat. Tell us the webbing width in in, how it is folded, and whether the loop is for our custom tie-down straps.


Check Section, Seam and Finish Before Sampling
The second decision is the ring body. Before you approve a sample, compare the wire diameter or plate thickness, corner radius, seam or weld closure and surface finish against the drawing, and run the actual webbing through it to look for sharp edges or a gap at the closure. If the ring will go on a finished strap, see our ratchet straps for how an assembly differs from a component.
Tell Us About Your Rectangular Rings
Share what you know. Partial information is fine, and our factory team will ask for what is missing.
Prefer to reach us another way? Visit our contact page.
How an Inquiry Moves Forward
-
1
Requirements and design
You send the application, webbing details and any drawing or photo.
-
2
Preproduction specification review
We check ring dimensions, section, closure and finish against your brief.
-
3
Sample approval
You compare the sample with the agreed specification before production.
-
4
Production
Production follows the approved specification and sample.
-
5
Shipping and payment review
Packing, freight terms and payment details are reviewed with you in the quote.
What to Specify for Your Quotation
The catalog p. 17 photograph shows the ring family, and the workbench photo shows our Vietnam factory hardware area. Your quotation sets the details. A ring on its own says nothing about a finished strap assembly, so tell us the following and we will confirm the configuration:
- Webbing width in in, and how the loop is folded and sewn.
- Inside width and height of the ring, wire diameter or plate thickness, and corner shape, all in in.
- Seam, weld or formed construction, material grade and finish you require.
- Any test evidence or documents you need for the named configuration and the U.S. market.
- Quantity, packing, private-label needs and destination.
Partial information is fine. Send Inquiry with what you have, ideally with a drawing, photo or sample, and our factory team will ask for the rest.
Packing for Loose Rings
Loose metal rings need packing that keeps finishes and welds from rubbing in transit. Bagging, cartons, labels and carton counts are agreed with you in the quotation for your configuration, and the packing we show for other products at the company level is not a promise for a specific ring.

Webbing Loops and Labels
The catalog p. 17 metal ring shown here is a loose part that can be reviewed as a companion to a sewn webbing loop. It is not automatically included with any strap. If you want rings supplied with sewn webbing loops, private-label tags or retail packing, tell us the intended layout and we will review it as a separate item. Our custom tie-down straps page shows how we handle custom webbing work.
Ring Resources
Browse the catalog page 17 ring photograph, a photo of our Vietnam factory hardware workbench, a specification sketch and a note on our factory process footage. For your own ring, attach your configuration drawing when you request a quote.


Specification sketch
- W — inside webbing width, measured across the opening, in in.
- H — inside height of the opening, in in.
- D — wire diameter or plate thickness of the ring body, in in. Shown at the top edge and in a small cross-section.
- Rounded corners; no weld-on mounting bracket in this sketch.
Buyer specification fields
Fields a buyer typically gives us when specifying a rectangular ring, based on how third-party component specification sheets are organized:
- Inside webbing width (in)
- Inside height/opening (in)
- Wire diameter or plate thickness (in)
- Welded/formed/snap construction
- Material grade and finish
- Component-specific test evidence
Lengths of finished long straps and rolls use documented whole ft; local component and short-end dimensions use in. This sketch explains the geometry only and does not set a supply size.
We check the drawing revision and sample for each metal fitting before quoting U.S. orders. Dimensions and ratings are confirmed for the quoted configuration.
When you request a quote, attach your own configuration drawing, photo or sample details. The schematic above is an explanatory sketch, and the catalog p. 17 image is a photograph, not a drawing.
Third-party references
- Third-party reference US Cargo Control specification reference
-
Third-party component drawing
D-Ring Spec Sheet
For the referenced third-party item only; not a DEWIN production drawing.
Third-party values are not DEWIN specifications. No third-party ratings or dimensions are copied into our product specifications. Production drawings are reviewed with the quotation.
We can also work from your drawing, a sample or a photo.
Factory process footage
Our Vietnam factory has process footage of webbing looms and yarn racks, strap sewing and assembly, and a tensile-test machine. It shows how we work. It is not a performance test of a ring or of any specific SKU, and it does not establish a rated load.
If you would like to see footage relevant to your project, mention it in your inquiry.

Source: DEWIN catalog, page 17 — metal rectangular webbing ring photograph, shown as a family reference. Width, opening, thickness, material grade and exact SKU are specified with your quotation. Tell us which catalog reference you are working from in your inquiry, and we will match it to a configuration before quoting.
Why Send Your Ring Brief to Our Factory
Our approach is a clear, documented review of your drawing and sample, so you know what is included in your quotation.
Specification first
We ask for internal width and height, section, corners, seam or weld and finish before we quote.
Drawing and photo matching
Each photo or drawing is matched to a specific ring shape before it is used in a quote.
Direct factory contact
Your inquiry goes to our team at Dewin Technology Company Limited, not through a generic catalog form.
Quote scope in writing
Price, packing, terms and available documents are stated for your named configuration in the quote.
Customer Brands
These are DEWIN customer brands. The authorized catalog images below identify our company-level customer relationships; they do not establish a purchase, approval or load rating for the specific product category on this page.
Rectangular Ring FAQ
How long does a rectangular ring order take?
Lead time depends on the ring dimensions, closure type, finish, quantity and whether webbing work is included. Send your specification and order details, and we will state the timing in your actual quote.
Can I approve a sample after I place an order?
Sample approval is a step before production in our workflow. Whether a sample comes before or after the order, and on what terms, is confirmed in the quote for your configuration.
How long does shipping to the United States take?
Shipping time depends on packing, destination, freight method and terms. Include your delivery location in the inquiry, and we will confirm shipping details with the quote.
How will I know the status of my order?
Order updates are arranged with you through the contact details you provide, once the order terms are agreed in the quote.
Can I get samples of rectangular rings?
Send a drawing, photo or your own ring sample with the webbing it must fit. Sample availability, cost and shipping depend on the configuration and are confirmed with the quote.
Related Articles
Buyer guides on webbing materials, anchor hardware and how to prepare a purchasing brief. You can also browse the blog or visit our contact page.
Material comparison
Polyester, Nylon and Polypropylene Webbing
Compare the common webbing materials so you can choose the right one before sizing the hardware that goes with it.
Anchor interfaces
Tie-Down Hook and Ring Selection
A guide to the anchor interfaces on a tie-down strap and how hooks and rings differ in use.
Purchasing brief
U.S. Tie-Down Strap Specification Worksheet
A worksheet to help you prepare a clear purchasing brief before you send an inquiry to our factory.